Ablestik导电银胶ABLEBOND 8380B TDS

PRODUCT DESCRIPTION
ABLEBOND 8380B provides the following product
characteristics:
Technology Epoxy
Appearance Silver
Cure Heat cure
Product Benefits • Electrically conductive
• Fast cure at low temperatures
• Low resin bleed
Application Die attach
Filler Type Silver
Typical Package
Application
Charge Couple Device (CCD)
ABLEBOND 8380B adhesive is designed for medium die
attach applications.
TYPICAL PROPERTIES OF UNCURED MATERIAL
Thixotropic Index (0.5/5 rpm) 2.0
Viscosity, Brookfield CP51, 25 °C, mPa·s (cP):
Speed 5 rpm 10,000
Work Life @ 25°C, hours 48
Shelf Life @ -40°C (from date of manufacture), year 1
TYPICAL CURING PERFORMANCE
Cure Schedule
15 minutes @ 150°C
The above cure profiles are guideline recommendations. Cure
conditions (time and temperature) may vary based on customers'
experience and their application requirements, as well as customer
curing equipment, oven loading and actual oven temperatures.
TYPICAL PROPERTIES OF CURED MATERIAL
Electrical Properties:
Volume Resistivity, ohms-cm 0.0002
TYPICAL PERFORMANCE OF CURED MATERIAL
Die Shear Strength:
2 X 2 mm , psi,
cured 15 minutes @ 150ºC
Substrate
Ag/Cu Leadframe 1400

GENERAL INFORMATION
For safe handling information on this product, consult the
Material Safety Data Sheet, (MSDS).
THAWING:
1. Allow container to reach room temperature before use.
2. After removing from the freezer, set the syringes to stand
vertically while thawing.
3. Refer to the Syringe Thaw time chart for the thaw time
recommendation.
4. DO NOT open the container before contents reach 25°C
temperature. Any moisture that collects on the thawed
container should be removed prior to opening the
container.
5. DO NOT re-freeze. Once thawed to -40°C, the adhesive
should not be re-frozen.
Temperature, °C
Syringe Thaw Time, Minutes
30
20
10
0
-10
-20
-30
-40
0 10 20 30 40 50
1cc
3cc 10cc 30cc
DIRECTIONS FOR USE
1. Thawed adhesive should be immediately placed on
dispense equipment for use.
2. If the adhesive is transferred to a final dispensing
reservoir, care must be exercised to avoid entrapment of
contaminants and/or air into the adhesive.
3. Adhesive must be completely used within the products
recommended work life of 24 hours.
4. Silver-resin separation may occur if the adhesive is left
out at 25°C beyond the recommended work life.
Not for product specifications
The technical data contained herein are intended as reference
only. Please contact your local quality department for
assistance and recommendations on specifications for this
product.

Storage
Store product in the unopened container in a dry location.
Storage information may be indicated on the product container
labeling.
Optimal Storage: -40 °C. Storage below minus (-)40 °C or
greater than minus (-)40 °C can adversely affect product
properties.
Material removed from containers may be contaminated during
use. Do not return product to the original container. Henkel
Corporation cannot assume responsibility for product which
has been contaminated or stored under conditions other than
those previously indicated. If additional information is required,
please contact your local Technical Service Center or
Customer Service Representative.
Conversions
(°C x 1.8) + 32 = °F
kV/mm x 25.4 = V/mil
mm / 25.4 = inches
N x 0.225 = lb
N/mm x 5.71 = lb/in
N/mm² x 145 = psi
MPa x 145 = psi
N·m x 8.851 = lb·in
N·m x 0.738 = lb·ft
N·mm x 0.142 = oz·in
mPa·s = cP
Note
The data contained herein are furnished for information only
and are believed to be reliable. We cannot assume
responsibility for the results obtained by others over whose
methods we have no control. It is the user's responsibility to
determine suitability for the user's purpose of any production
methods mentioned herein and to adopt such precautions as
may be advisable for the protection of property and of persons
against any hazards that may be involved in the handling and
use thereof. In light of the foregoing, Henkel Corporation
specifically disclaims all warranties expressed or implied,
including warranties of merchantability or fitness for a
particular purpose, arising from sale or use of Henkel
Corporation’s products. Henkel Corporation specifically
disclaims any liability for consequential or incidental
damages of any kind, including lost profits. The discussion
herein of various processes or compositions is not to be
interpreted as representation that they are free from
domination of patents owned by others or as a license under
any Henkel Corporation patents that may cover such
processes or compositions. We recommend that each
prospective user test his proposed application before repetitive
use, using this data as a guide. This product may be covered
by one or more United States or foreign patents or patent
applications.

下载附件参看PDF版本：
  ABLEBOND 8380B-EN (61.8 KB, 6 次)
您没有权限下载此文件。