{"id":3113,"date":"2012-07-22T22:20:16","date_gmt":"2012-07-22T14:20:16","guid":{"rendered":"http:\/\/www.g4e.cn\/wordpress\/?p=3113"},"modified":"2013-11-19T14:33:07","modified_gmt":"2013-11-19T06:33:07","slug":"henkel-hysol-es4512-tds","status":"publish","type":"post","link":"http:\/\/www.g4e.cn\/wordpress\/datasheet\/3113.html","title":{"rendered":"HENKEL HYSOL ES4512 TDS"},"content":{"rendered":"

\u5f88\u5c11\u770b\u5230\u6c49\u9ad8\u65d7\u4e0b\u7684\u53cc\u7ec4\u5206\u704c\u5c01\u73af\u6c27\uff0c\u4eca\u5929\u6709\u5ba2\u6237\u54a8\u8be2\u5230\u4e00\u4e2a\uff0c\u6458\u5f55TDS\u5982\u4e0b\uff1a<\/p>\n

PRODUCT DESCRIPTION
\nHYSOL\u00ae ES4512\u2122 provides the following product\u00a0characteristics:<\/p>\n\n\n\n<\/colgroup>\n\n\n\n\n\n\n\n\n\n\n
Technology<\/span><\/td>\nEpoxy<\/span><\/td>\n<\/tr>\n
Appearance (Part A)<\/span><\/td>\nBlack<\/span><\/td>\n<\/tr>\n
Appearance (Part B)<\/span><\/td>\nTan<\/span><\/td>\n<\/tr>\n
Appearance (cured)<\/span><\/td>\nBlack<\/span><\/td>\n<\/tr>\n
Components<\/span><\/td>\nTwo component – requires mixing<\/span><\/td>\n<\/tr>\n
Mix\u00a0 Ratio,\u00a0 by\u00a0 volume – Part A: Part B<\/span><\/td>\n100 : 106<\/span><\/td>\n<\/tr>\n
Mix\u00a0\u00a0 Ratio,\u00a0\u00a0 by weight – Part A: Part B<\/span><\/td>\n100 : 100<\/span><\/td>\n<\/tr>\n
Cure<\/span><\/td>\nRoom temperature cure<\/span><\/td>\n<\/tr>\n
Application<\/span><\/td>\nPotting and Encapsulating<\/span><\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

HYSOL\u00ae ES4512\u2122 is a two-component casting system with excellent handling properties. This low cost, flexible system is filled with a non-abrasive filler for machine metering\/dispensing or regular hand mixer applications.<\/p>\n

UL Classification<\/strong><\/p>\n

Classified by Underwriters Laboratories Inc.<\/strong>\u00ae \u00a0<\/strong>UL-94 “Test for Flammability of Plastic Materials” and meets the requirements of 94VO in a 1.8 mm cross section.<\/p>\n

TYPICAL PROPERTIES OF UNCURED MATERIAL
\nPart A Properties
\n<\/strong><\/p>\n\n\n\n<\/colgroup>\n\n\n\n\n\n\n\n
Density @ 25 \u00b0C, g\/cm\u00b3<\/span><\/td>\n1.57<\/td>\n<\/tr>\n
Filler Content, %<\/span><\/td>\n50<\/td>\n<\/tr>\n
Solids Content, %<\/span><\/td>\n100<\/td>\n<\/tr>\n
Viscosity, Brookfield – RVF, 25 \u00b0C, mPa\u00b7s (cP):<\/span><\/td>\n<\/td>\n<\/tr>\n
Spindle 6, speed 2 rpm<\/span><\/td>\n55,000<\/td>\n<\/tr>\n
Spindle 6, speed 20 rpm<\/span><\/td>\n28,000<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

\u00a0Part B Properties
\n<\/strong><\/strong><\/p>\n\n\n\n<\/colgroup>\n\n\n\n\n\n\n
Density @ 25 \u00b0C, g\/cm\u00b3<\/span><\/td>\n1.48<\/td>\n<\/tr>\n
Filler Content, %<\/span><\/td>\n60<\/td>\n<\/tr>\n
Solids Content, %<\/span><\/td>\n100<\/td>\n<\/tr>\n
Viscosity, Brookfield – RVF, 25 \u00b0C, mPa\u00b7s (cP):<\/span><\/td>\n<\/td>\n<\/tr>\n
Spindle 5, speed 20 rpm<\/span><\/td>\n6300<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

Mixed Properties<\/strong><\/strong><\/strong><\/strong><\/p>\n\n\n\n<\/colgroup>\n\n\n\n\n\n\n\n\n
Density @ 25 \u00b0C, g\/cm\u00b3<\/span><\/td>\n1.55<\/td>\n<\/tr>\n
Peak Exotherm Temperature, \u00b0C:<\/span><\/td>\n<\/td>\n<\/tr>\n
200 g mass<\/span><\/td>\n90<\/td>\n<\/tr>\n
Pot Life @ 25 \u00b0C, minutes:<\/td>\n<\/td>\n<\/tr>\n
200 g mass<\/td>\n60<\/td>\n<\/tr>\n
Gel Time @ 25 \u00b0C, hours<\/td>\n5<\/td>\n<\/tr>\n
Viscosity @ 25 \u00b0C, mPa\u2219s (cP)<\/td>\n19000<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n

TYPICAL CURING PERFORMANCE Recommended Curing Conditions<\/strong><\/p>\n

36 to 48 hours @ 25 \u00b0C (Recommended cure)<\/p>\n

3 hours @ 60 \u00b0C (Alternate cure)<\/p>\n

TYPICAL PROPERTIES OF CURED MATERIAL
\nPhysical Properties:
\nGlass Transition Temperature, ASTM D 3418, \u00b0C 50
\nCoefficient of Thermal Expansion , ASTM D 3148, K-1:
\nPre Tg (alpha 1) 66\u00d710-6
\nPost Tg (alpha 2) 150\u00d710-6
\nCoefficient of Thermal Conductivity, ISO 8302, W\/(m\u00b7K) 0.644
\nLinear Shrinkage, ASTM D792, % 0.1
\nShore Hardness, ISO 868, Durometer D 88
\nWater Absorption, ISO 62, %:
\n24 hours in water @ 25 \u00b0C 0.32
\nElongation , ASTM D 638,% 6.3
\nTensile Strength Tests – Hysol:
\nTensile Strength, ASTM D 638 N\/mm\u00b2 18.4
\n(psi) (2,670)
\nCompressive Strength, ISO 604 N\/mm\u00b2 80.7
\n(psi) (11,700)
\nFlexural Strength, ASTM D790 N\/mm\u00b2 34.3
\n(psi) (4,975)
\nTear Strength, ISO 34-2, Die D N\/mm 42.0
\n(lb.\/in.) (240)
\nElectrical Properties:
\nDielectric Breakdown Strength IEC 60243-1, kV\/mm 44.7
\nVolume Resistivity, IEC 60093, \u03a9\u00b7cm:
\n@ 25 \u00b0C 5.9\u00d71014
\n@ 105 \u00b0C 2.8\u00d71010
\nSurface Resistivity, IEC 60093, \u03a9:
\n@ 25 \u00b0C 3.0\u00d71015
\n@ 105 \u00b0C 1.8\u00d71015
\nDielectric Constant \/ Dissipation Factor, IEC 60250:
\n@ 25 \u00b0C:
\n100-Hz 4.6 \/ 0.038
\n1-kHz 4.4 \/ 0.03
\n10-kHz 4.3 \/ 0.026
\n100-kHz 4.1 \/ 0.023
\n@ 105 \u00b0C:
\n100-Hz 35.7 \/ 1.43
\n1-kHz 9.2 \/ 0.5
\n10-kHz 7.8 \/ 0.1
\n100-kHz 7.2 \/ 0.08
\nGENERAL INFORMATION
\nFor safe handling information on this product, consult the\u00a0Material Safety Data Sheet, (MSDS).
\nNot for product specifications
\nThe technical data contained herein are intended as reference\u00a0only. Please contact your local quality department for\u00a0assistance and recommendations on specifications for this\u00a0product.<\/p>\n

Storage
\nStore product in the unopened container in a dry location.
\nStorage information may be indicated on the product container\u00a0labeling.
\nLiquid Storage – Liquids should be stored at 23\u00b0C or\u00a0below, in closed containers. If stored below 23\u00b0C, the\u00a0material MUST be allowed to come to room temperature, in\u00a0the sealed container, to avoid moisture contamination.
\nMaterial removed from containers may be contaminated during\u00a0use. Do not return product to the original container. Henkel\u00a0Corporation cannot assume responsibility for product which\u00a0has been contaminated or stored under conditions other than\u00a0those previously indicated. If additional information is required,\u00a0please contact your local Technical Service Center or\u00a0Customer \u00a0ervice Representative.
\nConversions
\n(\u00b0C x 1.8) + 32 = \u00b0F
\nkV\/mm x 25.4 = V\/mil
\nmm \/ 25.4 = inches
\nN x 0.225 = lb
\nN\/mm x 5.71 = lb\/in
\nN\/mm\u00b2 x 145 = psi
\nMPa x 145 = psi
\nN\u00b7m x 8.851 = lb\u00b7in
\nN\u00b7m x 0.738 = lb\u00b7ft
\nN\u00b7mm x 0.142 = oz\u00b7in
\nmPa\u00b7s = cP
\nNote
\nThe data contained herein are furnished for information only\u00a0and are believed to be reliable. We cannot assume\u00a0responsibility for the results obtained by others over whose\u00a0methods we have no control. It is the user’s responsibility to\u00a0determine suitability for the user’s purpose of any production\u00a0methods mentioned herein and to adopt such precautions as\u00a0may be advisable for the protection of property and of persons\u00a0against any hazards that may be involved in the handling and\u00a0use thereof. In light of the foregoing, Henkel Corporation\u00a0specifically disclaims all warranties expressed or implied,\u00a0including warranties of merchantability or fitness for a\u00a0particular purpose, arising from sale or use of Henkel\u00a0Corporation\u2019s products. Henkel Corporation specifically\u00a0disclaims any liability for consequential or incidental\u00a0damages of any kind, including lost profits. The discussion\u00a0herein of various processes or compositions is not to be\u00a0interpreted as representation that they are free from\u00a0domination of patents owned by others or as a license under\u00a0any Henkel Corporation patents that may cover such\u00a0processes or compositions. We recommend that each\u00a0prospective user test his proposed application before repetitive\u00a0use, using this data as a guide. This product may be covered
\nby one or more United States or foreign patents or patent\u00a0applications.<\/p>\n

\u534e\u4e3a\u7f51\u76d8\u4e0b\u8f7d\uff1ahttp:\/\/dl.dbank.com\/c0u22kruon<\/p>\n

\u6ce8\u518c\u672c\u5730\u4e0b\u8f7d\uff1a

\"\"  H-ES4512-EN TDS<\/strong> (67.2 KB, 4 \u6b21)
\u60a8\u6ca1\u6709\u6743\u9650\u4e0b\u8f7d\u6b64\u6587\u4ef6\u3002<\/i><\/p><\/p>\n","protected":false},"excerpt":{"rendered":"

\u5f88\u5c11\u770b\u5230\u6c49\u9ad8\u65d7\u4e0b\u7684\u53cc\u7ec4\u5206\u704c\u5c01\u73af\u6c27\uff0c\u4eca\u5929\u6709\u5ba2\u6237\u54a8\u8be2\u5230\u4e00\u4e2a\uff0c\u6458\u5f55TDS\u5982\u4e0b\uff1a PRODUCT DESCRIPTIO […]<\/p>\n","protected":false},"author":1,"featured_media":3736,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":[],"categories":[667],"tags":[634,633,635],"_links":{"self":[{"href":"http:\/\/www.g4e.cn\/wordpress\/wp-json\/wp\/v2\/posts\/3113"}],"collection":[{"href":"http:\/\/www.g4e.cn\/wordpress\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.g4e.cn\/wordpress\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.g4e.cn\/wordpress\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"http:\/\/www.g4e.cn\/wordpress\/wp-json\/wp\/v2\/comments?post=3113"}],"version-history":[{"count":0,"href":"http:\/\/www.g4e.cn\/wordpress\/wp-json\/wp\/v2\/posts\/3113\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"http:\/\/www.g4e.cn\/wordpress\/wp-json\/wp\/v2\/media\/3736"}],"wp:attachment":[{"href":"http:\/\/www.g4e.cn\/wordpress\/wp-json\/wp\/v2\/media?parent=3113"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.g4e.cn\/wordpress\/wp-json\/wp\/v2\/categories?post=3113"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.g4e.cn\/wordpress\/wp-json\/wp\/v2\/tags?post=3113"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}