{"id":2792,"date":"2011-12-08T21:57:45","date_gmt":"2011-12-08T13:57:45","guid":{"rendered":"http:\/\/www.g4e.cn\/wordpress\/?p=2792"},"modified":"2013-11-19T15:46:37","modified_gmt":"2013-11-19T07:46:37","slug":"ablestik-conductive-silver-glue-2030sc-tds","status":"publish","type":"post","link":"http:\/\/www.g4e.cn\/wordpress\/datasheet\/2792.html","title":{"rendered":"Ablestik \u5bfc\u7535\u94f6\u80f62030SC TDS"},"content":{"rendered":"<pre>PRODUCT DESCRIPTION\r\nABLEBOND 2030SC provides the following product\r\ncharacteristics:\r\nTechnology Proprietary Hybrid Chemistry\r\nAppearance Silver\r\nCure Heat cure\r\npH 4.5\r\nProduct Benefits \u2022 Snap curable\r\n\u2022 Low stress\r\nApplication Die attach\r\nFiller Type Silver\r\nKey Substrates Most metals\r\nABLEBOND 2030SC die attach adhesive has been formulated\r\nfor use in high throughput die attach applications. This material\r\nis designed to minimize stress and resulting warpage between\r\ndissimilar surfaces. It can be used in a variety of package sizes\r\n.\r\nTYPICAL PROPERTIES OF UNCURED MATERIAL\r\nThixotropic Index (0.5\/5 rpm) 4.6\r\nViscosity, Brookfield CP51, 25 \u00b0C, mPa\u00b7s (cP):\r\nSpeed 5 rpm 11,600\r\nWork Life @ 25\u00b0C, hours 24\r\nShelf Life @ -40\u00b0C (from date of manufacture), year 1\r\nTYPICAL CURING PERFORMANCE\r\nCure Schedule\r\n90 seconds @ 110\u00b0C\r\nAlternative Cure Schedule\r\n10 seconds @ 150\u00b0C\r\nWeight Loss on Cure\r\n10 x 10 mm Si die on glass slide, % 0.4\r\nThe above cure profiles are guideline recommendations. Cure\r\nconditions (time and temperature) may vary based on customers'\r\nexperience and their application requirements, as well as customer\r\ncuring equipment, oven loading and actual oven temperatures.\r\nTYPICAL PROPERTIES OF CURED MATERIAL\r\nPhysical Properties:\r\nThermal Conductivity, W\/mK 2.3<\/pre>\n<pre>Tensile Modulus, DMTA :\r\n@ -65 \u00b0C N\/mm\u00b2 6,200\r\n(psi) (900,000)\r\n@ 25 \u00b0C N\/mm\u00b2 3,300\r\n(psi) (480,000)\r\n@ 150 \u00b0C N\/mm\u00b2 350\r\n(psi) (50,000)\r\n@ 250 \u00b0C N\/mm\u00b2 450\r\n(psi) (65,000)\r\nExtractable Ionic Content, @ 100\u00b0C ppm:\r\nChloride (Cl-) &lt;20\r\nSodium (Na+) &lt;30\r\nPotassium (K+) &lt;5\r\nWeight Loss After Cure, %:\r\n16 hours Isothermal @ 125\u00baC 0.41\r\nRamp to 230\u00baC 0.5\r\nElectrical Properties:\r\nVolume Resistivity, ohms-cm:\r\ncured 90 seconds @ 110\u00baC 0.0002\r\nBond Joint Resistance, ohms:\r\ncured 90 seconds @ 110\u00baC, Cu\/Cu, 25\u03bcm Bondline 0.008\r\nTYPICAL PERFORMANCE OF CURED MATERIAL\r\nDie Shear Strength vs Substrate:\r\n2 X 2 mm die, kg-f,\r\nDie on Substrate: @ RT\r\nSi die on Pd 1.90\r\nAu die on SS 2.24\r\nAu die on Au 2.11\r\nDie Shear Strength vs Die Shear Temperature:\r\n3 X 3 mm Si die, kg-f,\r\ncured 90 seconds @ 110\u00baC\r\nSubstrate @25\u00b0C @150\u00b0C @200\u00b0C\r\nPBGA-FR4 1.90 0.96 0.87\r\nGENERAL INFORMATION\r\nFor safe handling information on this product, consult the\r\nMaterial Safety Data Sheet, (MSDS).\r\nTHAWING:\r\n1. Allow container to reach room temperature before use.\r\n2. After removing from the freezer, set the syringes to stand\r\nvertically while thawing.\r\n3. Refer to the Syringe Thaw time chart for the thaw time\r\nrecommendation.\r\n4. DO NOT open the container before contents reach 25\u00b0C\r\ntemperature. Any moisture that collects on the thawed\r\ncontainer should be removed prior to opening the\r\ncontainer.<\/pre>\n<pre>5. DO NOT re-freeze. Once thawed to -40\u00b0C, the adhesive\r\nshould not be re-frozen.\r\nTemperature, \u00b0C\r\nSyringe Thaw Time, Minutes\r\n30\r\n20\r\n10\r\n0\r\n-10\r\n-20\r\n-30\r\n-40\r\n0 10 20 30 40 50\r\n1cc\r\n3cc 10cc 30cc\r\nDIRECTIONS FOR USE\r\n1. Thawed adhesive should be immediately placed on\r\ndispense equipment for use.\r\n2. If the adhesive is transferred to a final dispensing\r\nreservoir, care must be exercised to avoid entrapment of\r\ncontaminants and\/or air into the adhesive.\r\n3. Adhesive must be completely used within the products\r\nrecommended work life of 24 hours.\r\n4. Silver-resin separation may occur if the adhesive is left\r\nout at 25\u00b0C beyond the recommended work life.\r\nNot for product specifications\r\nThe technical data contained herein are intended as reference\r\nonly. Please contact your local quality department for\r\nassistance and recommendations on specifications for this\r\nproduct.\r\nStorage\r\nStore product in the unopened container in a dry location.\r\nStorage information may be indicated on the product container\r\nlabeling.\r\nOptimal Storage: -40 \u00b0C. Storage below minus (-)40 \u00b0C or\r\ngreater than minus (-)40 \u00b0C can adversely affect product\r\nproperties.\r\nMaterial removed from containers may be contaminated during\r\nuse. Do not return product to the original container. Henkel\r\nCorporation cannot assume responsibility for product which\r\nhas been contaminated or stored under conditions other than\r\nthose previously indicated. If additional information is required,\r\nplease contact your local Technical Service Center or\r\nCustomer Service Representative.\r\nConversions\r\n(\u00b0C x 1.8) + 32 = \u00b0F\r\nkV\/mm x 25.4 = V\/mil\r\nmm \/ 25.4 = inches\r\nN x 0.225 = lb\r\nN\/mm x 5.71 = lb\/in\r\nN\/mm\u00b2 x 145 = psi\r\nMPa x 145 = psi\r\nN\u00b7m x 8.851 = lb\u00b7in\r\nN\u00b7m x 0.738 = lb\u00b7ft\r\nN\u00b7mm x 0.142 = oz\u00b7in\r\nmPa\u00b7s = cP<\/pre>\n<pre>Note\r\nThe data contained herein are furnished for information only\r\nand are believed to be reliable. We cannot assume\r\nresponsibility for the results obtained by others over whose\r\nmethods we have no control. It is the user's responsibility to\r\ndetermine suitability for the user's purpose of any production\r\nmethods mentioned herein and to adopt such precautions as\r\nmay be advisable for the protection of property and of persons\r\nagainst any hazards that may be involved in the handling and\r\nuse thereof. In light of the foregoing, Henkel Corporation\r\nspecifically disclaims all warranties expressed or implied,\r\nincluding warranties of merchantability or fitness for a\r\nparticular purpose, arising from sale or use of Henkel\r\nCorporation\u2019s products. Henkel Corporation specifically\r\ndisclaims any liability for consequential or incidental\r\ndamages of any kind, including lost profits. The discussion\r\nherein of various processes or compositions is not to be\r\ninterpreted as representation that they are free from\r\ndomination of patents owned by others or as a license under\r\nany Henkel Corporation patents that may cover such\r\nprocesses or compositions. We recommend that each\r\nprospective user test his proposed application before repetitive\r\nuse, using this data as a guide. This product may be covered\r\nby one or more United States or foreign patents or patent\r\napplications.<\/pre>\n<pre>\u4e0b\u8f7d\u9644\u4ef6\u67e5\u770bPDF\u6587\u4ef6\uff1a<p><img src=\"http:\/\/www.g4e.cn\/wordpress\/wp-content\/plugins\/hacklog-downloadmanager\/images\/ext\/pdf.gif\" alt=\"\" title=\"\" style=\"vertical-align: middle;\" \/>&nbsp;&nbsp;<strong>ABLEBOND 2030SC-EN<\/strong> (65.4 KB, 13 \u6b21)<br \/><i>\u60a8\u6ca1\u6709\u6743\u9650\u4e0b\u8f7d\u6b64\u6587\u4ef6\u3002<\/i><\/p><\/pre>\n","protected":false},"excerpt":{"rendered":"<p>PRODUCT DESCRIPTION ABLEBOND 2030SC provides the follow [&hellip;]<\/p>\n","protected":false},"author":1,"featured_media":3748,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":[],"categories":[667],"tags":[473,468,467,15],"_links":{"self":[{"href":"http:\/\/www.g4e.cn\/wordpress\/wp-json\/wp\/v2\/posts\/2792"}],"collection":[{"href":"http:\/\/www.g4e.cn\/wordpress\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.g4e.cn\/wordpress\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.g4e.cn\/wordpress\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"http:\/\/www.g4e.cn\/wordpress\/wp-json\/wp\/v2\/comments?post=2792"}],"version-history":[{"count":0,"href":"http:\/\/www.g4e.cn\/wordpress\/wp-json\/wp\/v2\/posts\/2792\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"http:\/\/www.g4e.cn\/wordpress\/wp-json\/wp\/v2\/media\/3748"}],"wp:attachment":[{"href":"http:\/\/www.g4e.cn\/wordpress\/wp-json\/wp\/v2\/media?parent=2792"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.g4e.cn\/wordpress\/wp-json\/wp\/v2\/categories?post=2792"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.g4e.cn\/wordpress\/wp-json\/wp\/v2\/tags?post=2792"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}