{"id":1908,"date":"2011-05-18T21:40:26","date_gmt":"2011-05-18T13:40:26","guid":{"rendered":"http:\/\/www.g4e.cn\/wordpress\/?p=1908"},"modified":"2013-11-19T16:04:46","modified_gmt":"2013-11-19T08:04:46","slug":"loctite-adhesive-3874-tds-loctite-thermal-data","status":"publish","type":"post","link":"http:\/\/www.g4e.cn\/wordpress\/datasheet\/1908.html","title":{"rendered":"\u4e50\u6cf0LOCTITE\u5bfc\u70ed\u80f6\u7c98\u52423874 TDS\u8d44\u6599"},"content":{"rendered":"

PRODUCT DESCRIPTION<\/strong><\/p>\n

3874\u2122 provides the following product characteristics:<\/p>\n

Technology <\/strong>Acrylic<\/p>\n

Chemical Type Acrylic ester<\/p>\n

Appearance (uncured) Light grey opaque fluid , No visible bubbles. Slight separation of filler acceptableLMS<\/p>\n

Components One component – requires no mixing<\/p>\n

Viscosity High, thixotropic<\/p>\n

Cure <\/strong>Activator<\/p>\n

Application <\/strong>Bonding<\/p>\n

 <\/p>\n

3874\u2122 is a thermally conductive adhesive. When used with Activator 7387\u2122, it cures rapidly to form a high strength, high modulus, thermoset acrylic polymer. Typical applications include bonding heat sinks to heat dissipating components such as BGAs in electronics applications. The thixotropic nature of 3874\u2122 reduces the migration of liquid product after application to the substrate.<\/p>\n

 <\/p>\n

TYPICAL PROPERTIES OF UNCURED MATERIAL<\/strong><\/p>\n

Specific Gravity@ 25 \u00b0C 2.08<\/p>\n

Flash Point – See MSDS<\/p>\n

Viscosity, Brookfield – HBT, 25 \u00b0C, mPa\u00b7s (cP):<\/p>\n

Spindle TB, speed 0.5 rpm, Helipath 800,000 to 1,800,000LMS<\/p>\n

Spindle TB, speed 5 rpm, Helipath 200,000 to 450,000LMS<\/p>\n

Cure Speed vs. Substrate<\/strong><\/p>\n

The rate of cure will depend on the substrate used. The graph below shows the shear strength developed with time on grit blasted steel lap shears and tested according to ISO 4587. (Activator 7387\u2122 applied to one surface).<\/p>\n

 <\/p>\n

TYPICAL PROPERTIES OF CURED MATERIAL<\/strong><\/p>\n

Cured for 24 hours @ 70 \u00b0C, followed by 7 days @ 22 \u00b0C<\/p>\n

Physical Properties<\/strong>:<\/p>\n

Coefficient of Thermal Expansion, ISO 11359-2, K-1\u00a0 76\u00d710-6<\/p>\n

Coefficient of Thermal Conductivity, ISO 8302, W\/(m\u00b7K) 1.25<\/p>\n

Glass Transition Temperature, \u00b0C 49 Shore Hardness, ISO 868, Durometer D 72<\/p>\n

Elongation, at break, ISO 37, % 3.2<\/p>\n

 <\/p>\n

Initial @ 22 \u00b0C.<\/p>\n

Electrical Properties<\/strong>:<\/p>\n

Volume Resistivity, IEC 60093, \u03a9\u00b7cm 4.3\u00d71014<\/p>\n

Surface Resistivity, IEC 60093, \u03a9 3.8\u00d71014<\/p>\n

Dielectric Breakdown Strength, IEC 60243-1, kV\/mm 23.6<\/p>\n

After 1 week @ 85 \u00b0C \/ 85% RH<\/p>\n

Electrical Properties<\/strong>:<\/p>\n

Volume Resistivity, IEC 60093, \u03a9\u00b7cm 1.5\u00d71014<\/p>\n

Surface Resistivity, IEC 60093, \u03a9 2.6\u00d71013<\/p>\n

Dielectric Breakdown Strength, IEC 60243-1, kV\/mm 3.5<\/p>\n

 <\/p>\n

TYPICAL PERFORMANCE OF CURED MATERIAL<\/strong><\/p>\n

Adhesive Properties<\/strong><\/p>\n

After 24 hours @ 22 \u00b0C, Activator 7387\u2122 on 1 side Lap Shear Strength, ISO 4587: Steel N\/mm\u00b2 \u226511.7LMS<\/p>\n

(psi) (\u22651,695)<\/p>\n

Aluminum N\/mm\u00b2 \u22657LMS (psi) (\u22651,015)<\/p>\n

 <\/p>\n

GENERAL INFORMATION<\/strong><\/p>\n

This product is not recommended for use in pure oxygen and\/or oxygen rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials For safe handling information on this product, consult the Material Safety Data Sheet (MSDS).<\/strong><\/p>\n

 <\/p>\n

Directions for use:<\/strong><\/p>\n

1. For best performance bond surfaces should be clean and free from grease.<\/p>\n

2. Apply Activator 7387\u2122 to one of the bond surfaces and the adhesive to the other surface. Parts should be assembled immediately..<\/p>\n

3. Excess adhesive can be wiped away with organic solvent.<\/p>\n

4. Bond should be held clamped until adhesive has fixtured.<\/p>\n

5. Product should be allowed to develop full strength before subjecting to any service loads (typically 24 to 72 hours after assembly, depending on bond gap, materials and ambient conditions).<\/p>\n

 <\/p>\n

Loctite Material Specification<\/strong>LMS<\/strong><\/p>\n

LMS dated March-07, 2003. Test reports for each batch are available for the indicated properties. LMS test reports include selected QC test parameters considered appropriate to specifications for customer use. Additionally, comprehensive controls are in place to assure product quality and consistency. Special customer specification requirements may be coordinated through Henkel Quality.<\/p>\n

 <\/p>\n

Storage<\/strong><\/p>\n

Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling. Optimal Storage: 2 \u00b0C to 8 \u00b0C. Storage below 2 \u00b0C or greater than 8 \u00b0C can adversely affect product properties. <\/strong>Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated. If additional information is required, please contact your local Technical Service Center or Customer Service Representative.<\/p>\n

 <\/p>\n

\"\"  loctite 3874 TDS<\/a><\/strong> (59.7 KB, 232 \u6b21)<\/p>\n","protected":false},"excerpt":{"rendered":"

PRODUCT DESCRIPTION 3874\u2122 provides the following produc […]<\/p>\n","protected":false},"author":1,"featured_media":3732,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":[],"categories":[667],"tags":[367,368,366],"_links":{"self":[{"href":"http:\/\/www.g4e.cn\/wordpress\/wp-json\/wp\/v2\/posts\/1908"}],"collection":[{"href":"http:\/\/www.g4e.cn\/wordpress\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.g4e.cn\/wordpress\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.g4e.cn\/wordpress\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"http:\/\/www.g4e.cn\/wordpress\/wp-json\/wp\/v2\/comments?post=1908"}],"version-history":[{"count":0,"href":"http:\/\/www.g4e.cn\/wordpress\/wp-json\/wp\/v2\/posts\/1908\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"http:\/\/www.g4e.cn\/wordpress\/wp-json\/wp\/v2\/media\/3732"}],"wp:attachment":[{"href":"http:\/\/www.g4e.cn\/wordpress\/wp-json\/wp\/v2\/media?parent=1908"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.g4e.cn\/wordpress\/wp-json\/wp\/v2\/categories?post=1908"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.g4e.cn\/wordpress\/wp-json\/wp\/v2\/tags?post=1908"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}